Compuprint 3046 Programmer Manual Instrukcja Użytkownika

Compuprint 30X6 Programmer Manual

Hex 1B 42 n1 n2 . . . nk 00 Decimal 27 66 n1 n2 . . . nk 0 Parameter range 0 　k 　16 1 　n 　255 nk > n(k-1) Function Sets vertical tab posi

5 Sweden 6 Italy 7 Spain I 8 Japan (English) 9 Norway 10 Denmark II 11 Spain II 12 Latin America ESC % Select user-defined set Format ASCII

Hex 1B 67 Decimal 27 103 Function Selects 15-cpi character printing ESC SP Set character space Format ASCII ESC SP n Hex 1B 20

Decimal 27 72 Function Cancels double-strike printing selected with the ESC G command ESC q Select character style Format ASCII ESC q n Hex

Cancels double-width printing selected by the SO or ESC SO commands ESC W Turn double-width printing on/off Format ASCII ESC W n Hex 1

Parameter range 0 　nL 　255 0 　nH 　31 m = 0, 1, 2, 3, 6, 32, 33, 38, 39, 40 Function Prints dot-graphics in 8, 24,depending on the following parame

Format ASCII ESC E Hex 1B 45 Decimal 27 69 Function Sets the weight attribute of the font to bold ESC F Cancel bold font Format ASCII

3 LF Line feed 4 ESC 0 Select 1/8-inch line spacing 5 ESC + n Set n/360-inch line spacing 6 ESC 2 Select 1/6-inch line spacing 7 ESC

44 BS Backspace 45 ESC @ Initialize printer 46 ESC U n Turn unidirectional mode on/off 47 ESC X n1 n2 Set the left/right margin 48 ESC f Se

34 ESC Y Cancel the underline printing mode 35 ESC U Set double extended printing mode 36 ESC R Cancel the horizontal extended mode for ANK characte

Contents Commands...3 1．Index f

IInntteerrffaacceess This appendix provides technical information for the parallel and serial interfaces 11.. TThhee PPaarraalllleell IInntteerrff

OOppeerraattiinngg PPhhaasseess The link protocol is mainly based on the following three phases: • Negotiation Phase This phase is activated always

Signal Name Pin N° Source Description AUTOFEEDXT 14 HOST Active low level signal. GND 16 - Logical ground level (0V). CHASSIS GND 17 - Fr

The pins 1 to 14 of the printer are connected to the pins with the same number of the parallel port of the host. The pins 19 to 30 of the printer are

IInntteerrffaaccee TTiimmiinngg Timing and Handshaking depend upon the connection mode. Mode Centronics: Our Centronics mode supports the BUSY-W

The least significant bit of the data bits is sent first after the start bit. The number of data bits is selected via menu. The parity bit, when prese

44.. NNeettwwoorrkk iinntteerrffaaccee Cable connector: 8pin, RJ45 The following table lists the network interface signals used: PPiinn NNaammee

CCoommmmaannddss 11．．IInnddeexx ffoorr EESSCC//PPKK NO Command Function 1 ESC ( C Set page length in defined unit 2 ESC ( U Set unit 3 ESC C Set

37 DC4 Cancel double-width printing (one line) 38 ESC W Turn double-width printing on/off 39 ESC w Turn double-height printing on/off 4

77 DC1 Select printer 78 DC3 Deselect printer 79 ESC # Cancel MSB control 80 ESC = Set MSB to 0 81 ESC > Set MSB to 1 82 ESC j Reverse paper feed 2

ESC C NUL Set page length in inches Format ASCII ESC C NUL n Hex 1B 43 00 n Decimal 27 67 0 n Parameter range 1 　n 　22 Function Se

Format ASCII ESC l n Hex 1B 6C n Decimal 27 108 n Parameter range 1 　n 　255 0 　(left margin) <(right margin) Function Sets the left

HT Tab horizontally Format ASCII HT Hex 09 Decimal 9 Function Moves the horizontal print position to the next tab to the right of the curr

ASCII ESC 3 n Hex 1B 33 n Decimal 27 51 n Parameter range 0 　n 　255 Function Sets the line spacing to n/180 inch ESC + Set n/360-inc