Compuprint 4247-Z03 Programmer Manual Instrukcja Użytkownika Strona 356
- Strona / 380
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Serial Interface Signals
The following table lists the RS-232/C serial interface signals:
Signal Name Pin Number
Local
Connect.
Source
Remote
Connect.
Source Description
SIGNAL
GROUND
5 – – Always connected to the 0 Volts of the Power Supply
TXD 3 Printer Printer Transmitted Data Signal (an output from printer). A
MARK condition is held during IDLE communication
state. An indeterminate state is present when printer is
powered off.
RXD 2 Host Data Set Received data signal (an input to printer).
RTS 7 Printer Printer Request to Send Signal (an output from printer). Active
HIGH level signal. It is HIGH until the printer is
powered off, then an indeterminate state is present .
CTS 8 Data Set Active HIGH level signal indicates that the host or data
set is ready to receive data from the printer.
DSR 6 Data Set Active HIGH level signal. Indicates that the host or data
set is ready to be connected to the printer and is ready
for data transfer.
DCD 1 Data Set Active HIGH level signal. Indicates that the host is
transmitting or the data set is receiving the Data Carrier
signal.
2nd RTS 9 Printer Functionally equivalent to the DTR signal.
DTR 4 Printer Printer Data Terminal Ready. Normally HIGH (ON). Indicates
that the printer is ready to initiate a connection.
LAN Interface Port
LAN Interface Port
1. Ethernet 10/100BaseT Connector
2. Green 10/100Mbit/sec. Transmission Speed LED
3. Yellow Traffic LED
LED Indicators
The LED indicator modes are described in the following table:
LED Status Description
Yellow LED Unlit Transmission speed at 10Mbit/sec.
Lit Transmission speed at 100Mbit/sec.
Green LED Blinks Transmitting or receiving packets from the network.
USB Interface Port
USB 2.0 full speed 12/Mbit/sec. interface.
336 Programmer Manual
- MAN10299.00.00 1
- Contents 3
- Contents v 5
- Contents vii 7
- Contents ix 9
- Programmer Manual 10
- Contents xi 11
- Printer description 17
- Print speeds 17
- Paper paths 17
- Print qualities 18
- Printer interfaces 18
- Printer datastream emulations 18
- How to Use This Manual 19
- Print Job Processing 21
- Page Printing Concept 21
- Page Presentation 21
- 2 Programmer Manual 22
- PPDS Compatibility 24
- One-Byte Controls 24
- Null (NUL) 24
- Bell (BEL) 24
- 6 Programmer Manual 26
- Cancel (CAN) 27
- Escape (ESC) 27
- Escape Sequence Controls 27
- 8 Programmer Manual 28
- Null (ESC NUL) 29
- Bell (ESC BEL) 29
- Backspace (ESC BS) 29
- Horizontal Tab (ESC HT) 29
- Line Feed (ESC LF) 29
- Vertical Tab (ESC VT) 30
- Form Feed (ESC FF) 30
- Carriage Return (ESC CR) 30
- Cancel (ESC CAN) 31
- Auto Underscore (ESC -) 32
- 14 Programmer Manual 34
- Set Vertical Tabs (ESC B) 35
- Set Page Length (ESC C) 35
- 16 Programmer Manual 36
- End Skip Perforation (ESC O) 38
- Set Default Tabs (ESC R) 39
- Set Print Direction (ESC U) 40
- Print All Characters (ESC \) 41
- Reverse Line Feed (ESC ]) 41
- Continuous Overscore (ESC _) 42
- Relative Move Right (ESC d) 42
- Relative Move Left (ESC e) 42
- Select Line Scoring (ESC [ -) 42
- 1B 5B 40 LL HH M1 M2 M3 M4 43
- 1B 5B 49 02 00 HF LF 43
- 24 Programmer Manual 44
- 26 Programmer Manual 46
- 4247 Commands 48
- Control Hex Name 49
- 14 14 1B 21 NN 01 PP 19 49
- 14 14 1B 21 NN 02 PP 19 49
- 14 14 1B 21 NN 03 PP 19 49
- 30 Programmer Manual 50
- 14 14 1B 21 NN 07 PP 19 51
- 14 14 1B 21 NN 11 PP 19 51
- 14 14 1B 21 NN 12 PP 19 51
- 32 Programmer Manual 52
- 14 14 1B 21 NN 17 PP 19 53
- 14 14 1B 21 NN 18 PP 19 53
- 34 Programmer Manual 54
- 36 Programmer Manual 56
- 14 14 1B 69 NN 57
- 14 14 1B 70 NN 57
- Buffer Terminating Conditions 58
- 40 Programmer Manual 60
- 42 Programmer Manual 62
- Space (SP) 64
- Delete Character (DEL) 64
- 48 Programmer Manual 68
- Master Select (ESC !) 69
- Cancel MSB Control (ESC #) 69
- 50 Programmer Manual 70
- Select Graphics Mode (ESC *) 71
- Auto Underscore (ESC –) 71
- Select Italic Mode (ESC 4) 72
- Cancel Italic Mode (ESC 5) 72
- Initialize Printer (ESC @) 74
- Set Horizontal Tabs (ESC D) 75
- End Emphasized Print (ESC F) 75
- 56 Programmer Manual 76
- 1B 57 NN 79
- 1B 59 LL HH NN...NN 79
- 1B 5A LL HH NN...NN 79
- Set Relative Position (ESC \) 80
- Double High Printing (ESC w) 82
- 64 Programmer Manual 84
- 14 14 1B 21 NN 05 PP 19 85
- 14 14 1B 21 NN 06 PP 19 85
- 66 Programmer Manual 86
- 14 14 1B 21 NN 14 PP 19 87
- 14 14 1B 21 NN 16 PP 19 87
- {DATA2} EM) 88
- 70 Programmer Manual 90
- 14 14 1B 59 NN 91
- 14 14 1B 5A NN 91
- 14 14 1B 67 NN 91
- 14 14 1B 68 91
- Select Print Quality 92
- 74 Programmer Manual 94
- Overview 95
- Physical Medium 95
- IPDS Coordinate Systems 96
- Logical Page Layout 97
- I and B Coordinate System 98
- Processing IPDS Commands 99
- IPDS Command Format 100
- Acknowledge Reply (ACK) 102
- Host Acknowledgment Requests 103
- IPDS Data 104
- Mixing Rules 105
- Page State 106
- IPDS Operating States 106
- Home State 106
- Overlay State 107
- Page Segment State 108
- 90 Programmer Manual 110
- 92 Programmer Manual 112
- Page Segment Sequence 114
- Overlay Sequence 115
- Page Sequence 116
- Error Handling 117
- 98 Programmer Manual 118
- IPDS Initialization Defaults 119
- Parameter Values 120
- Command Format 120
- Command Function Sets 122
- No Operation (NOP) 123
- Sense Type and Model (STM) 123
- 104 Programmer Manual 124
- Set Home State (SHS) 126
- Load Font Equivalence (LFE) 127
- 108 Programmer Manual 128
- Code Page ID Values 129
- Load Copy Control (LCC) 130
- Logical Page Descriptor (LPD) 131
- 112 Programmer Manual 132
- Logical Page Position (LPP) 133
- Deactivate Font (DF) 134
- End Page (EP) 134
- End (END) 134
- 116 Programmer Manual 136
- 118 Programmer Manual 138
- 120 Programmer Manual 140
- 122 Programmer Manual 142
- Execute Order Any State (XOA) 144
- Activate Printer Alarm (APA) 145
- Discard Buffered Data (DBD) 145
- Request Resource List (RRL) 145
- 126 Programmer Manual 146
- 128 Programmer Manual 148
- 130 Programmer Manual 150
- Print Quality Control (PQC) 152
- Text Function Set Commands 153
- Load Equivalence (LE) 153
- Write Text (WT) 154
- Set Inline Margin (SIM) 155
- Set Baseline Increment (SBI) 155
- Absolute Move Inline (AMI) 156
- Absolute Move Baseline (AMB) 156
- Relative Move Inline (RMI) 156
- Relative Move Baseline (RMB) 156
- Begin Line (BLN) 157
- Set Coded Font Local (SCFL) 157
- Set Text Orientation (STO) 157
- Begin Suppression (BSU) 157
- End Suppression (ESU) 158
- Draw I-Axis Rule (DIR) 158
- Draw B-Axis Rule (DBR) 158
- Repeat String (RPS) 159
- Transparent Data (TRN) 159
- Set Text Color (STC) 159
- Overstrike (OVS) 160
- Underscore (USC) 161
- Temporary Baseline Move (TBM) 161
- Image Function Set Commands 162
- Write Image Control (WIC) 162
- from the X-coordinate and 163
- from the X 163
- Write Image (WI) 164
- Graphic Window 166
- Graphic Block Area 166
- Write Graphics Control (WGC) 168
- Graphic Output Control (GOC) 170
- Graphic Data Descriptor (GDD) 171
- 152 Programmer Manual 172
- Area Mapping Control Options 173
- 154 Programmer Manual 174
- Self-Describing Instructions 176
- 158 Programmer Manual 178
- Write Graphics (WG) 179
- 160 Programmer Manual 180
- No Operation 181
- Segment Characteristics 181
- Set Pattern Set 182
- Set Color 182
- Set Background Mix 183
- Set Fractional Line Width 183
- Set Line Type 183
- Set Line Width 184
- Set Current Position 184
- Set Arc Parameters 184
- Set Extended Color 185
- Set Pattern Symbol 185
- Set Marker Symbol 186
- Set Character Cell Size 186
- Set Character Angle 187
- Set Character Set 187
- Set Character Precision 187
- Set Character Direction 188
- Set Marker Precision 188
- Set Marker Set 188
- End Prologue 188
- End Area 188
- Begin Area 189
- Line at Current Position 190
- Marker at Current Position 190
- Fillet at Current Position 191
- Full Arc at Current Position 192
- Image Data 192
- in drawing 193
- Character String 194
- Full Arc 195
- from the previous end point 196
- from the first end point 197
- from the 197
- point. If there are no 197
- 178 Programmer Manual 198
- 180 Programmer Manual 200
- Write Bar Code Control (WBCC) 201
- 182 Programmer Manual 202
- 184 Programmer Manual 204
- 186 Programmer Manual 206
- 188 Programmer Manual 208
- Write Bar Code (WBC) 210
- 192 Programmer Manual 212
- Overlay Function Set Commands 213
- Begin Overlay (BO) 214
- Delete Overlay (DO) 214
- Include Overlay (IO) 214
- Begin Page Segment (BPS) 215
- Include Page Segment (IPS) 215
- Deactivate Page Segment (DPS) 216
- Load Symbol Set (LSS) 216
- 198 Programmer Manual 218
- Data Check - X'08' 220
- 202 Programmer Manual 222
- 204 Programmer Manual 224
- 206 Programmer Manual 226
- 208 Programmer Manual 228
- 210 Programmer Manual 230
- temporary baseline 231
- 212 Programmer Manual 232
- 214 Programmer Manual 234
- Text Print Samples 235
- Bar Codes 236
- Graphics Patterns 237
- Graphics Example 238
- 220 Programmer Manual 240
- 222 Programmer Manual 242
- IPDS Coding Example 243
- 224 Programmer Manual 244
- 226 Programmer Manual 246
- 228 Programmer Manual 248
- 230 Programmer Manual 250
- Appendix A. Code Pages 251
- 232 Programmer Manual 252
- USA/Canada/Canadian Bilingual 253
- Canadian French 254
- Austrian/German 255
- Belgian Old 256
- Brazilian 257
- Danish/Norwegian 258
- Finnish/Swedish 259
- 240 Programmer Manual 260
- Japanese English 261
- Portuguese 262
- Spanish/Spanish Speaking 263
- English (UK)/Ireland 264
- Japanese Katakana 265
- French/French Azerty 266
- Appendix A. Code Pages 247 267
- Greek (Old) 268
- Hebrew Bulletin 269
- International 5/Swiss/Belgian 270
- Appendix A. Code Pages 251 271
- 252 Programmer Manual 272
- Appendix A. Code Pages 253 273
- Latin 2/ROECE 274
- Icelandic 275
- Greek New + euro 276
- Cyrillic 277
- Yugoslav (Old) 278
- Appendix A. Code Pages 259 279
- 260 Programmer Manual 280
- Latin 9 (ISO 8859) + euro 281
- Cyrillic Multilingual 282
- Latin-5 Turkey 283
- 264 Programmer Manual 284
- Baltic Multilingual 285
- Estonian 286
- USA/Canada + euro 287
- Austrian/German + euro 288
- Danish/Norwegian + euro 289
- Finnish/Swedish + euro 290
- Italian + euro 291
- 272 Programmer Manual 292
- English/UK + euro 293
- French + euro 294
- Appendix A. Code Pages 275 295
- Icelandic + euro 296
- ASCII Code Pages 297
- USA (Personal Computer) A-54 298
- Greek (MS DOS) 299
- Greek/Latin (ISO 8859-7) 300
- Latin 1 (ISO 8859-1) 301
- PC Multilingual 302
- Old Greek 303
- Latin 3 (PC) 305
- Cyrillic (PC) 306
- Latin 5-Turkey + euro 307
- PC Multilingual + euro 308
- Appendix A. Code Pages 291 311
- Appendix A. Code Pages 293 313
- PC Data, Cyrillic, Russian 315
- Appendix A. Code Pages 297 317
- 298 Programmer Manual 318
- Appendix A. Code Pages 299 319
- Latin 2 (ISO 8859-2) 320
- Latin 3 (ISO 8859-3) 321
- Latin 4 (ISO 8859-4) 322
- Cyrillic (ISO 8859-5) 323
- Latin 8 (ISO 8859-8) 324
- Latin 5 (ISO 8859-9) 325
- Latin 9 (ISO 8859-15) + euro 328
- Appendix A. Code Pages 309 329
- Arabic Extended 330
- Latin 6 (ISO 8859-6) 331
- Farsi (Personal Computer) 332
- Estonian (Personal Computer) 333
- Latvian (Personal Computer) 334
- Appendix A. Code Pages 315 335
- Central Europe Latin 2 336
- Cyrillic Windows + euro 337
- Epson FX-series Code Pages 338
- Italic Character Table 339
- 320 Programmer Manual 340
- PSF usage - z/OS and System i 341
- 322 Programmer Manual 342
- 324 Programmer Manual 344
- OCR Symbols 345
- OCR Scanning 346
- Press STOP 347
- 328 Programmer Manual 348
- Appendix E. Interfaces 349
- Parallel Interface Signals 350
- Appendix E. Interfaces 331 351
- 332 Programmer Manual 352
- Appendix E. Interfaces 333 353
- Interface Timing 354
- The Serial Interface 355
- Serial Interface Signals 356
- LAN Interface Port 356
- USB Interface Port 356
- 338 Programmer Manual 358
- 340 Programmer Manual 360
- 342 Programmer Manual 362
- Descriptions 364
- 346 Programmer Manual 366
- 348 Programmer Manual 368
- 350 Programmer Manual 370
- 352 Programmer Manual 372
- 354 Programmer Manual 374
- 356 Programmer Manual 376
- Notices 377
- 358 Programmer Manual 378
Powiązane produkty i podręczniki dla Drukarki Compuprint 4247-Z03 Programmer Manual
Drukarki Compuprint 9058 Instrukcja Użytkownika
(145 strony)
(145 strony)
Drukarki Compuprint 9058 Instrukcja Użytkownika
(147 strony)
(147 strony)
Drukarki Compuprint 9058 Instrukcja Użytkownika
(84 strony)
(84 strony)
Drukarki Compuprint 9058 Instrukcja Użytkownika
(151 strony)
(151 strony)
Drukarki Compuprint 9058 Instrukcja Użytkownika
(85 strony)
(85 strony)
Drukarki Compuprint 9060LA Instrukcja Użytkownika
(177 strony)
(177 strony)
Drukarki Compuprint 9070 Instrukcja Użytkownika
(171 strony)
(171 strony)
Drukarki Compuprint 9070 Instrukcja Użytkownika
(172 strony)
(172 strony)
Drukarki Compuprint 9070 Instrukcja Użytkownika
(171 strony)
(171 strony)
Drukarki Compuprint 9070 Instrukcja Użytkownika
(171 strony)
(171 strony)
Drukarki Compuprint 6214 Instrukcja Użytkownika
(70 strony)
(70 strony)
Drukarki Compuprint 6314 Instrukcja Użytkownika
(78 strony)
(78 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji